RGBlink VSP 5360 Manual de usuario descargar pdf (Pagina 2)

Step 13-Power

Step 12-Serial Port

How to Zoom the Image

Image vertical and horizontal zoom, the effect can

stretch the image according to one direction.

Push [MENU] button, and enter the menu, rotate the

knob and choose [INPUT SETUP], push the knob to

confirm and choose <ZOOM>, push the knob to

confirm, settings are as follows:

V UP: Enlarge the image from the top.

V DOWN: Enlarge the image from the bottom.

V UP/DOWN: Enlarge the image from the top and

the bottom.

H LEFT: Enlarge the image from the left.

H RIGHT: Enlarge the image from the right.

H LEFT/RIGHT: Enlarge the image from the left and

the right.

CENTER: Enlarge the image from the center.

RESET: If quality image distorts by mistake in

improper operation, it can be initialized operation to

recover factory setting

Power On

How to Scale the Image

Push [Scale/Position] button, and enter the SCALE

menu, button 0-9 lights are on, user can input the

number or rotate the knob to set the vertical size and

horizontal size.

SCALE menu are as follows:

H SIZE: Width setting.

V SIZE: Height setting.

RESET: If quality image distorts by mistake in

improper operation, it can be initialized operation to

recover factory setting.

How to Realize Single Image Switching

1.Boot the system default CV1 to the current input

source (key on and flashes ). If need seamless switch

to other source such as DVI1, push DVI1 key.

2.Push DVI1 buttons, CV1 button is off, and DVI1 key

lights, single image switching (that is switch CV1 to

DVI1) is finished.The same method for CV2, CV3,

VGA1, VGA2, DVI1, DVI2, DVI3, DP1, DP2, SDI1

input signal switching.

How to Add or Clear the Layer

1. In EFFECTS area, add the layer according to actual

need, that is push any key of layer A, B, C, D (or

select all the 4 keys), key lights and flashes means

the layer is selected, and add layer finished.

2. In EFFECTS area, push any key of layer A, B, C, D

that need to clear, key flashes. Push the key again,

key light is off, and clear layer finished.

How to Set up the Position of the Image

1. Push [Scale/Position] button two times, the button

lights, user can set up the position of the image.

2. Rotate the knob, and adjust the vertical and

horizontal position.

3. If quality image distorts by mistake in improper

operation, it can be initialized operation to recover

factory setting.

4. Push any other button, [Scale/Position] button light

is off, and close the position setting function.

VSP 5360 Quick Start

Version 1.1

Page 2 of 4

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: rgblinkc[email protected]m http://www.rgblink.cn

T568A cable end

color

T568B cable end

color

1 White-green White-orange

2 Green Orange

3 White-green White-green

4 Blue Blue

5 White-blue White-blue

6 White-orange green

7 White-brown White-brown

8 Brown Brown

Definition of crosswire

CAT5

crosswire is

one end in

T568A

standard, the

other in

T568B

standard.

T568A T568B

End terminal

Connect the back panel RJ11 port and RS232 port to

a control system on computer with RS232-to-RJ11

cable. Below is the definition.

RS-232 Function

2 TX Transmit

3 RX Receive

5 GND Ground Signal

7 --- Not used

8 --- Not used

RS-422 Function

TX- Transmit(-)

RX- Receive(-)

GND Ground Signal

RX+ Receive(+)

TX+ Transmit(+)

Insert a

crosswire to

RJ11 port

RJ-11 Function

TX Transmit

2 RX Receive

GND Ground Signal4

--- Not used

Insert a

crosswire into

RS232/RS422

port

Plug in power cord with IEC connector, VSP 5360

supports AC power from 85~264V AC, 50~60Hz,

which means world wide compatible.

Push power button to ON position. LCD module on the

front panel will show RGBlink and VSP 5360 model

information, and go into self-verification, then it will load

the last setting configuration data and send the processed

video to target display or device. CV1 input is the default

input source. User can operate VSP 5360 with front panel

buttons or remote control with windows control software

run on computer, by RS232, USB or TCP/IP port.

Local Control Front Panel Operation

Mega Systems Inc., US Distributor of RGBLink

www.megasystemsinc.com • [email protected]

Toll Free: 866-460-MEGA • Local: 210-684-2600

5718 Kenwick St., San Antonio, TX 78238

1 2 3 4

Comentarios a estos manuales

Sin comentarios

RGBlink VSP 5360 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Receptor RGBlink VSP 5360